• Oversized screen with with a dual mode display is easy to read.
• Posi-click buttons mount on the shift lever(s) and easily accommodates sweaty fingers.
• Beautiful, low profile, center mounting design. The computer head is just 2 inches (5 cm) long by 1.79 inches (4.5 cm) wide and only .6 of an inch (1.5 cm) thick.
• Perfectly integrates into most STI levers including 10 speed models. Will work with older, pre 1999, STI levers but not all functions will be available. See the charts below for details.
• Functions include virtual cadence, digital gear number, gear indicator bar, current speed, average speed, maximum speed, cumulative distance and trip distance in miles or kilometers.
• Enough memory to store information for up to four bicycles.
• Programmable so you do not lose cumulative distance when you change the battery.
• The bubbles in the rear Optical Gear Display are removable for use with less than 10 speeds. You can show just 8 or 9 bubbles if that is how many rear gears you have. You may also program 1, 2 or 3 chainrings.
• Time functions include: 12/24 hour clock and time elapsed on your current ride, a lap counter and stop watch.
• Three extra stop watch functions are ideal for time trials and laps. They are: distance, average speed and maximum speed.
• Auto start/stop automatically starts and stops the ride time stopwatch when you start or stop cycling. Auto start/stop assures you of the greatest possible accuracy for elapsed time and average speed functions.
• Accepts wheels from 26 x 1 to 700 x 28.

• Works with double or triple cranksets and 8, 9 or 10 speed cassettes or 8 speed freewheels. Will even work with Campy cassettes as long as you use Shimano shifters and a Shimano rear derailleur.
• Compatible with all Shimano rear derailleurs including the Rapid Rise model.
• Accepts input for one cassette only; does not allow for wheel changes with different size cassettes unless you reprogram the settings. However, you may program any tooth configuration from 11 to 40 teeth for your cassette.
• You may use a double or triple crankset. All sizes of chainrings may be programmed in by you.
• Requires a front wheel sensor and pickup but not a cadence sensor.
• Cadence is virtual; Flight Deck calculates it from what gears you are in and how fast you are moving. Cadence is displayed even when you are coasting.
• Easy to install. Takes little time to set up.
• Data can be reviewed on or off the bike.
• Single spoke pickup fits all round spoked wheels. Use our CY-55-56 magnet for non-spoked wheels.
• A mounting kit is required and sold separately. The mounting kit must be matched to your handlebar mounted road or mountain shift levers.
• Waterproof and lightweight. Only 52 grams!
• Solidly backed with a two year manufacturers warranty from Shimano USA.
• Warranty service and help with technical questions is available from Shimano USA in Irvine, California USA. Call Shimano USA at 800-423-2420, FAX them at (949) 951-7519 or visit them at Shimano.com by clicking on the underlined text . You may also download official Flight Deck manuals in Adobe pdf format from the Shimano web site.

All Shimano STI levers may be used with a Flight Deck computer. All functions except Virtual Cadence, Gear Indicator and the Gear Ratio display will work fine on any STI lever. To use Virtual Cadence, Gear Indicator and the Gear Ratio display plus all of the other functions your levers must be 100% Flight Deck compatible. An easy way to check for 100% compatibility is to:

1) Check for the words "Flight Deck" on the lever assembly.
2) Check for rubber buttons on the road STI lever hood(s). Do you have two buttons on the right and none on the left hood or one button on each hood?
3) Look inside the lever for a flat, ribbon like wire cable.

The ribbon cable is not always easy to see and a few older, pre-2000, levers did not have rubber buttons on the hoods. However all 100% Flight Deck compatible STI levers do have the "Flight Deck" script.

• Match this kit with Dura-Ace 7700-C, Tiagra ST-4400 and Sora ST-3300 and 3303 STI levers. All of these levers have a single button on each hood.
• These kits also fit year 2001 to current Ultegra 6510 and 105 5500-CA STI levers. 2001 Ultegra and 105 STI levers came with a single button on EACH hood. Pre-2001 Ultegra and 105 9 speed STI levers have two buttons on the right hood and none on the left. Replace the two button hoods with one button hoods and you may use these kits with your pre-2001 Ultegra and 105 STI 9 speed levers.
• The SM-6501 kit features a start/stop button on the left STI lever and a mode select button on the right STI lever.
• Dura-Ace 7700-C, Tiagra ST-4400 and Sora ST-3300 and 3303 ST are new for the year 2000. They and all post 2000 8 and 9 speed STI levers have a sensor built into them that tells the Flight Deck computer what position chainring and cassette cog you are currently using. 7 speed Sora levers lack the built in sensor. Sora 8 speed STI levers have the sensor.
• These kits will NOT work with older Dura-Ace 7700 9 speed, Dura-Ace 7400 8 speed, Ultegra or 105 8 speed STI levers.
• The SM-6501 wireless kit comes with a 26.8 and a 31.8 mm oversized handlebar clamp.
• ALL Flight Deck computer functions are useable with this kit.
• In the wireless kit, SM-6501, wires still lead under your handlebar tape to the STI levers. However, the wires to the front wheel pickup were eliminated for a cleaner appearance. All computer functions remain the same. You may use the SM-6501 kit with an older, 6500, 6501 or current 6502 Flight Deck computer head.
• Warranty service and help with technical questions is available from Shimano USA in Irvine, California USA. Call Shimano USA at 800-423-2420, FAX them at (949) 951-7519 or visit them at Shimano.com by clicking on the underlined text .

• Some older, pre-2000, Shimano STI levers do not come with Flight Deck compatible hoods. Others may have outdated, two buttons on the right side, hoods.
• Dura-Ace 7700C and Tiagra hoods have a single button on each hood.
  Ultegra 6510 and 105 5500CA hoods also have a single button on each hood.
• Replacing outdated two button hoods with newer, single button hoods, allows you to use the SM 6500-RS wired and SM 6501 wireless kit with ALL 1999 to current Ultegra and 105 STI levers.

• All hoods are black and can be used with or without a Flight Deck computer.
• Compatible hoods are molded on the inside to hold the Flight Deck switches perfectly.
• Flight Deck compatible hoods listed below come as a pair even though some applications only require that you change the right hood.
• Warranty service and help with technical questions is available from Shimano USA in Irvine, California USA. Call Shimano USA at (949) 951-5003, FAX them at (949) 951-7519 or visit them at Shimano.com by clicking on the underlined text .

• Allows you to put handlebar mounted accessories above, below or in front of your handlebars. Mounts on your handlebars, stem or even your seatpost. The extension arm pivots 180 degrees.
• Two sizes are available. Both employ a 140 mm (5.6 inches) extension measured from the center of the bar clamp to the center of the horizontal accessory bar.
  The small Swing Grip comes with a 100 mm (4 inches) horizontal accessory bar while the large size has a 130 mm (5.1 inches) horizontal bar.
• Both sizes are available in satin silver or gloss black.
• Fits all road or MTB handlebars from 22mm (7/8 of an inch) to 35mm (1 3/8 of an inch) in diameter. May also be clamped to seatposts and larger frame tubes. Ideal for extra tail lights.

• Both horizontal accessory mounting bars may be adjusted side to side by 20 mm ( 3/4 of an inch). The 100 mm bar will hold two bar mounted accessories while the 130 will hold three.
• The horizontal accessory mounting bar may be rotated 360 degrees in 90 degree increments which makes the Swing Grip ideal for recumbents or non-bicycle applications. The extension bar pivots or swings 180 degrees. It may be locked in any position by simply tightening a 3mm allen bolt.
• Stainless steel clamp band, anodized silver or enameled black, alloy tube and carbon/plastic extension are well made and exceptionally durable.
• Easy to install. Requires a 3 mm allen wrench and a Phillips screwdriver. The allen wrench is included.
• Weighs only 91 or 97 grams.
• Warranty service and help with technical questions is available from the official Minoura USA Service Center in Hayward, California. Call them at (510) 538-8599 or email them at MinouraUSA@ATTGlobal.Net by clicking on the underlined text .
• More product information is also available at the Official Minoura Web Site in Japan.
  Minoura product manuals may be downloaded. They are in Adobe PDF format and require Adobe Acrobat Reader 4.0 or higher to read or print.

All of the computers we carry come as complete units; you do not need to purchase anything extra for standard bicycle applications. However, if you would like to set your computer up for a non-standard application or just need extra parts we have them. Choose what you need from the items listed below.

• Shimano Flight Deck O/S handlebar clamps for road and mountain wireless kits. 31.8 mm for oversized handlebars.
  CY-65-64 Wireless 31.8 Bar Clamp $9.88
  
  


• Flight Deck wireless transmitter. Requires a separate Clamp Band Kit for mounting. Comes with out a battery. Fits road and mountain kits.
  CY-65-62 Wireless Transmitter $12.88
  
  


• Flight Deck wireless transmitter mounting kit. Allows the above Flight Deck wireless transmitter to be attached to your fork. Fits road and mountain kits.
  CY-65-63 Transmitter Mount Kit $9.88
  
  


• Cronometro NOB. A universal computer mount that fits on ALL mountain or road stems or handlebars including clip on aero style bars. Allows the computer head to be mounted 90 degrees to what the original bracket was designed for. Tightens like a hose clamp; note the screw at the bottom.
  HB-31-60 $12.88

• Extra replacement battery for the older 6500 and current 6501 Flight Deck computer head.
  BA-10-10 Computer Head Battery $4.88
• Extra replacement battery for the Flight Deck fork mounted transmitter.
  BA-10-18 Transmitter Battery $4.88
  
  



• Flight Deck single spoke wheel magnet. Fits all front or rear, round wire, spoked wheels. May be used with ALL Flight Deck wiring kits.
  CY-65-55 Round Spoke Magnet $9.88
  
  



• Flight Deck single spoke wheel magnet. Fits all front or rear, flat wire, 14 gauge (2.0 mm) spoked wheels. May be used with ALL Flight Deck wiring kits. Simply snaps on to your bladed spoke.
  CY-65-56 Flat Spoke Magnet $14.88
  
  

• Single spoke wheel magnet, fits all front or rear, round wire, spoked wheels. Easy to modify for use with bladed or flat spoked wheels like Mavic Ksyrium, Campy Neutron, Zipp, etc. Simply widen the spoke hole by passing it over a fine toothed hack saw blade three to five times. May be used with any Sigma Sport, Vetta, Topeak or Cateye bike computer.
  CY-72-30 Round/Flat Spoke Magnet $4.88
  
  



• Adhesive backed, sticks on and secures with a zip tie which is included. Can also be used as a disc or bladed wheel magnet. Ideal for motorized applications like motorcycles, Karts, etc. Note the slot at the bottom which the zip tie threads through and securely holds this magnet in place.
  CY-32-08 Sticky Backed Magnet $4.88
  
  

At Branford Bike we want you to be happy and satisfied with everything you purchase from us. We understand that sometimes you will need to return a product because it was not quite what you wanted. You may return anything you purchase from us within 60 days and unused, for an immediate exchange or refund.

Our Secure Order Form is easy to use. Simply fill in the boxes as you would for a traditional paper catalog order form.

Our Secure Order Form opens in a separate window that you may resize and tile behind our online catalog. After filling in your name, address and card information you may leave the order window open. Browse through our catalog and when you wish to purchase an item simply "cut and paste" the part number and description to the appropriate order form boxes.

When you are done shopping, submit your order for error checking, and then for processing. We will email you a confirmation within 10 minutes. Another, more detailed confirmation, will follow when we ship your order.

   
We accept Visa, Discover and MasterCard for payment.
We will NOT charge your card until your order is shipped.

To print this page:
Use your browser's Print command or
press Ctrl + P on Windows, or Command + P on Mac.